Tin tức

Áp lực phun tốt nhất cho bộ thu bụi máy phản lực xung là gì?

Áp suất phun là gì? Áp suất phun: áp suất tại đó van xung được mở và khí nén được bơm vào bộ thu bụi. Áp suất thổi càng cao, tốc độ thổi càng nhanh và hiệu quả làm sạch càng tốt. Sau khi giảm áp suất của bộ lọc túi được hạn chế, áp suất phun càng cao, the greater the processing...

Cách đối phó với bộ sưu tập bụi khác nhau?

Hygroscopic deliquescent dust Hygroscopic and deliquescent dusts such as CaO, Na2CO3, NaHCO3, NaCI, vân vân. are easy to absorb moisture and harden on the surface of the filter bag, or become viscous liquid after deliquescence. It will cause difficulty in cleaning, large pressure loss, and even force the dust collector to fail. When dealing with hygroscopic and deliquescent dust, the following should be...

Nguyên nhân phân tích và dung dịch ngưng tụ sương trong bộ thu bụi túi xung

Analysis of Condensation Causes The condensation, đề cập đến hiện tượng độ ẩm bão hòa được kết tủa từ không khí ẩm ở áp suất và nhiệt độ nhất định. The temperature point at which moisture is released is called the dew point. The higher the gas pressure at saturation, điểm sương càng thấp. Độ ẩm trong không khí càng cao, điểm sương càng cao...

Làm đúng cách cài đặt bộ thu bụi

Các biện pháp phòng ngừa cho hoạt động hàng ngày của máy hút bụi xung (1) Khi hệ thống thu bụi hoạt động bình thường, the ash discharge cannot be stopped. Avoid dust accumulation in the hopper and force the dust collector to stop. Smoke and ash from the exhaust port indicate that the filter bag has been leaked. If any filter bag mouth is found to have dust...

Làm thế nào để đối phó với khói và bụi được tạo ra bởi việc phát điện đốt chất thải

1. Particulate Matter Control The flue gas from the cooling tower is neutralized by the slaked lime and activated carbon injection system, and then enters the bag filter and is discharged from the top of the compartment. The injected activated carbon and other particulate matter adhere to the surface of the filter bag to form a layer of filter cake; the...

Những điểm chính của thiết kế chống cháy nổ của máy hút bụi

1 Điều kiện nổ 1.1 pulverized coal temperature Different coal types have different ignition temperatures, nhưng để có bột than mịn hơn, due to the increased specific surface area, the explosion temperature is much lower than its ignition point. Usually the ignition temperature is below 40 . 1.2 Volatile matter of pulverized coal The combustible gas produced by the heating of pulverized coal is burned before...

Phương pháp ngưng tụ và xử lý bụi nhà máy xi măng

Giới thiệu về ví dụ ngưng tụ nhà máy xi măng 1 Example of high temperature type mill The cement mill with a diameter of 4.5m × 12.96m in a factory is a circular flow mill with a cyclone separator, and the end of the mill is dedusted by a flat-bag type dust collector. The mill system is indoors, the air convection between the mill and the...

Thiết kế và lựa chọn máy hút bụi lò điện công nghiệp

Phân loại lò điện công nghiệp: Lò điện trở, lò cảm ứng, lò chân không, lò chùm tia điện tử, xử lý nhiệt (hoặc luyện kim) đơn vị, heat treatment auxiliary equipment, combustion furnace. Industrial electric furnace dust removal mainly uses bag filter, and the dust hood is designed according to different working conditions on site. Therefore, the difficulty of industrial electric furnace dust removal lies in the design and arrangement of...